+Ethernet eth0: MAC address 00:00:00:00:54:33
IP: 192.168.0.93/255.255.255.0, Gateway: 0.0.0.0
Default server: 192.168.0.13, DNS server IP: 0.0.0.0

RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version v2_0 - built 08:14:43, Aug 22 2006

Platform: Cirrus Logic EDB9302 Board (ARM920T) Rev A
Copyright (C) 2000, 2001, 2002, Red Hat, Inc.

RAM: 0x00000000-0x02000000, 0x00041e68-0x01fdd000 available
FLASH: 0x60000000 - 0x61000000, 128 blocks of 0x00020000 bytes each.
RedBoot> 
RedBoot> fis load ramdisk.gz
RedBoot> load -v -r -b 0x80000 -m http /9302/zImagea

Raw file loaded 0x00080000-0x0015f2ab, assumed entry at 0x00080000
RedBoot> exec -r 0x800000 -s 0x800000 -c "console=ttyAM root=/dev/ram"
Using base address 0x00080000 and length 0x000df2ac
Uncompressing Linux............................................................... done, booting the kernel.

Linux version 2.6.8.1-crus2.0.2 (ivan@debian) (gcc version 3.4.1) #10 Wed Sep 6 15:44:21 EEST 2006
CPU: ARM920Tid(wb) [41129200] revision 0 (ARMv4T)
CPU: D VIVT write-back cache
CPU: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Machine: edb9302
Memory policy: ECC disabled, Data cache writeback
	bank 0 start at 0x00000000, length 0x00800000, mapped to 0xc0000000
	bank 1 start at 0x01000000, length 0x00800000, mapped to 0xc1000000
	bank 2 start at 0x04000000, length 0x00800000, mapped to 0xc4000000
	bank 3 start at 0x05000000, length 0x00800000, mapped to 0xc5000000
Built 1 zonelists
Kernel command line: console=ttyAM root=/dev/ram
PID hash table entries: 512 (order 9: 4096 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 8MB 8MB 8MB 8MB = 32MB total
Memory: 22088KB available (1596K code, 415K data, 64K init)
Calibrating delay loop... 99.73 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 8192K
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
NetWinder Floating Point Emulator V0.97 (double precision)
ttyAM0 at MMIO 0x808c0000 (irq = 52) is a EP93XX
ttyAM1 at MMIO 0x808d0000 (irq = 54) is a EP93XX
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
ep93xxusb ep93xxusb0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET: Registered protocol family 1
NET: Registered protocol family 17
RAMDISK: Compressed image found at block 0
usb 1-1: new full speed USB device using address 2
scsi0 : SCSI emulation for USB Mass Storage devices
Using anticipatory io scheduler
  Vendor: Kingston  Model: DataTraveler 2.0  Rev: 5.00
  Type:   Direct-Access                      ANSI SCSI revision: 02
SCSI device sda: 2013184 512-byte hdwr sectors (1031 MB)
sda: assuming Write Enabled
sda: assuming drive cache: write through
 sda: unknown partition table
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0,  type 0
VFS: Mounted root (ext2 filesystem).
Freeing init memory: 64K

init started:  BusyBox v1.00 (2006.01.19-17:26+0000) multi-call binary
lo: driver changed get_stats after register
eth0: driver changed get_stats after register

Please press Enter to activate this console. 

BusyBox v1.00 (2006.01.19-17:26+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

~ #